Somapop' UDS Build

Feel free to ask any questions, one of the experts will certainly respond, don't be afraid to ask anything, we were all beginners at some point.
YetiDave
Rubbed and Ready
Rubbed and Ready
Posts: 721
Joined: 28 Jun 2012, 19:30
First Name: Dave
Location: Manchester

Re: Somapop' UDS Build

Post by YetiDave »

It's more a hard glue that came with the fire rope, but it should work :D I've been using Sainsburys basics lumpwood all summer. At £1/kg it's great!
somapop
Got Wood!
Got Wood!
Posts: 149
Joined: 02 Jul 2014, 10:05
First Name: dave

Re: Somapop' UDS Build

Post by somapop »

Oh right - I'll look out for heat resistant silicone as well then!

Re lumpwood...thought you might have a local fella who handcrafts chunks of charcoaled walnut with his bare teeth for a very reasonable sum :D
Well, if that supermarket stuff is good enough, I'll know where to go (that Unicorn lump wood is pretty good value - considering it's local woodsman produced - at around £5 for 5 Kg. Those Big K briquettes (fiver from Morrisons) aren't too bad - no chemical smells, but a royal pain to light.
Do you cook in the winter? I'd like to think (once this is in use) I will...might be a bit harder to source charcoal then :(
YetiDave
Rubbed and Ready
Rubbed and Ready
Posts: 721
Joined: 28 Jun 2012, 19:30
First Name: Dave
Location: Manchester

Re: Somapop' UDS Build

Post by YetiDave »

I do cook in winter yeah. I'm going to stockpile as much as I can before the end of BBQ season! 40kg or so should keep me going :)

I've ordered from Liverpool Wood Pellets in the past. Not sure what their current rates are though
scuba-doo
Got Wood!
Got Wood!
Posts: 36
Joined: 05 Jan 2014, 15:07
First Name: david

Re: Somapop' UDS Build

Post by scuba-doo »

Re the wobbly ball valve. I used the same valve on mine and just used my angle grinder to reduce the amount of threads so the nut tightened up fully. I couldn't be bothered to go back out for washers.
somapop
Got Wood!
Got Wood!
Posts: 149
Joined: 02 Jul 2014, 10:05
First Name: dave

Re: Somapop' UDS Build

Post by somapop »

scuba-doo wrote:Re the wobbly ball valve. I used the same valve on mine and just used my angle grinder to reduce the amount of threads so the nut tightened up fully. I couldn't be bothered to go back out for washers.
That's even easier than grinding the flange off! Glaringly obvious now!
Bit late though as a plumber is passing on that part (with a bit of pipe)...it will do exactly the same thing butlook a little more technical 8-)

Cheers.
somapop
Got Wood!
Got Wood!
Posts: 149
Joined: 02 Jul 2014, 10:05
First Name: dave

Re: Somapop' UDS Build

Post by somapop »

YetiDave wrote:I do cook in winter yeah. I'm going to stockpile as much as I can before the end of BBQ season! 40kg or so should keep me going :)

I've ordered from Liverpool Wood Pellets in the past. Not sure what their current rates are though
Thanks yetidave - I'll probably do that too. Most of the supermarkets (haven't tried Sainsburys) only seem to stock briquettes pre drenched in lighter fuel :(
Cheers.
YetiDave
Rubbed and Ready
Rubbed and Ready
Posts: 721
Joined: 28 Jun 2012, 19:30
First Name: Dave
Location: Manchester

Re: Somapop' UDS Build

Post by YetiDave »

Aye, that stuff's pants. I've never really used good briquettes to be honest. If we both run out or get stuck during winter, we could always split a delivery of some? Just a thought. It'll be cheaper buying in bulk :)
essexsmoker
Rubbed and Ready
Rubbed and Ready
Posts: 1093
Joined: 31 May 2013, 18:32
First Name: Ant

Re: Somapop' UDS Build

Post by essexsmoker »

What paint did you use? I'm at the outside paint stage with mine. I have high temp paint but it needs to get to 350C to cure. When fired up the other day it hit 182C and just sat there. Im tempted to go for hammerite or something.
YetiDave
Rubbed and Ready
Rubbed and Ready
Posts: 721
Joined: 28 Jun 2012, 19:30
First Name: Dave
Location: Manchester

Re: Somapop' UDS Build

Post by YetiDave »

Yeah mine said 350 too. I never bothered! It's been several months now and no paint has washed or chipped off
essexsmoker
Rubbed and Ready
Rubbed and Ready
Posts: 1093
Joined: 31 May 2013, 18:32
First Name: Ant

Re: Somapop' UDS Build

Post by essexsmoker »

YetiDave wrote:Yeah mine said 350 too. I never bothered! It's been several months now and no paint has washed or chipped off
Oh ok, I'll just bang it on and wack up the temp as high as I can get. Thanks.
Post Reply